Glossary of Terms
Our team of spray foam insulation experts have compiled this glossary of terms to help you understand everything related to our services and hopefully clear up any confusion.
If you have any further enquiries regarding our residential and commercial property insulation services, don't hesitate to contact our team today on 0800 690 6338.
Occurs between building materials and is a major cause of condensation and mould growth in buildings. There are several varieties of mould that can grow on the inside surface of buildings in certain conditions and some can be toxic. Products with little or no cold bridging thus provide a healthy environment by reducing moisture and mould growth.
The maximum compressive stress a material can withstand without failure. Materials with high compressive strength thus have good load bearing capacity
K-Value Or Λ (Lambda) Value
The thermal conductivity of a material, the lower the value the better the material is at storing heat and retaining temperatures. Expressed in Watts per metre per degree Centigrade or Kelvin (W/mK).
A thermal bridge is a localised area of lower thermal resistance in the building envelope resulting in higher heat flow and lower internal surface temperatures. As well as increasing heat loss from the building envelope, thermal bridging can cause localised condensation as surface temperatures may be reduced below the dew point (condensation temperature) of the air in the space. This is a particular danger in buildings where the Relative Humidity (RH) may be high, such as canteens, laundries, swimming pools and some factories.
Measure of the ability of a solid or liquid to transfer heat.
Thermal conductivity is a material property. It will not differ with the dimensions of a material, but it is dependent on the temperature, the density and the moisture content of the material. The thermal conductivity normally found in tables is the value valid for normal room temperature.
Generally, light materials are better insulators than heavy materials because light materials often contain air enclosures. Dry still air has a very low conductivity. A layer of air will not always be a good insulator though, because heat is easily transferred by radiation and convection.
When a material, for instance, insulating material, becomes wet, the air enclosures fill with water and, because water is a better conductor than air, the conductivity of the material increases. That is why it is very important to install insulation materials when they are dry and take care that they remain dry. Vapour permeability ‘Breathable’ is used as a short way of saying ‘a high level of water vapour permeability’.
The U-value concept is used to quantify heat loss through plane elements of the building envelope or shell. U-value is defined as the overall thermal transmittance of a particular construction element (a wall or a roof for example), including the effect of surface resistance. It depends upon the thickness and thermal conductivity of its component layers and, in the case of air cavities, the emissivity of the surfaces.
Units of thermal transmittance are expressed in Wm²K.
The term ‘U’ represents overall thermal conductance from the outside to inside covering all modes of heat transfer. From the above equation, ‘U-value’ can be defined as the rate of heat flow over the unit area of any building component through unit overall temperature difference between both sides of the component.
The U-value is an important concept in building design. It represents the air-to-air transmittance of an element. This refers to how well an element conducts heat from one side to the other, which makes it the reciprocal of its thermal resistance. Thus, if we calculate the thermal resistance of an element or R-value, we can simply invert it to obtain the U-value.
Insulation is rated in terms of thermal resistance, called R-value, which indicates the resistance to heat flow. The higher the R-value, the greater the insulating effectiveness.
R = l/k
Where: R = the thermal resistance per unit area of the piece of material (m²K/W),
l = represents the thickness of the material (m), and
k = represents the conductivity of the material (W/mK).
Utilising the highest quality spray foam insulation products and hiring only fully-qualified insulation experts, we are your leading choice for commercial and residential insulation. For a service that offers a designated project manager, value for money and energy efficient products, why look elsewhere? Contact our team of experts today on 0800 690 6338 to discuss your requirements and find out how we can help improve the efficiency of your building.